||IP67, 4 x M12|
||4 x M12|
Protected against solid foreign bodies having a diameter of 12.5 mm or larger and against finger contact, not protected against water.
Protected against solid foreign bodies having a diameter of 1.0 mm or larger, protected against access with a wire, no protection against water.
Protection against dust in damaging amounts, complete protection against contact, protection against splashing water in any angle.
Dust-tight, full protection against contact, protection against spray water (jet) from any angle.
Dust-tight, full protection against contact, protection against temporary immersion.
Motor module to control geared motors with frequency inverters.
"SEW MOVI-SWITCH® 1E":
Motor module to control motor starters MOVI-SWITCH® 1E.
"SEW MOVI-SWITCH 2S, Lenze Smart Motor":
Motor module to control motor starters MOVI-SWITCH® 2S or to control Lenze Smart motors.
"Lenze Smart Motor":
Motor module to control Lenze Smart motors and to control additional sensors.
"Itoh Denki (PM500ME/XE/XP, PM605ME/XE/XP)":
Motor module to control 24 V motorized rollers Itoh Denki Serie Power Moller® 500ME/XE/XP and Serie Power Moller® 605ME/XE/XP.
"Interroll (EC310), RULMECA (RDR BL-2)":
Motor module to control 24 V motorized rollers Interroll Typ EC310 or RULMECA Typ RDR BL-2.
"Interroll (EC200, EC300), Rollex (Typ 840)":
Motor module to control 24 V motorized rollers Interroll Typ EC200 and EC300 or Rollex Typ 840.
"Interroll (EC310), RULMECA (RDR BL-2), Itoh Denki (PM500ME/XE/XP, PM605ME/XE/XP)":
Motor module to control 24 V motorized rollers Interroll Typ EC310 (also suitable for EC200 and EC300) or RULMECA Typ RDR BL-2 or Itoh Denki Serie Power Moller® 500ME/XE/XP and Serie Power Moller® 605ME/XE/XP.
Number of Drives
Line protection fuse
"yes, separatly for each motor, 3,5 A (slow-blow fuse)":
In the motor module UL approved fuses are placed before each of the motor supply connections. A short circuit in the motor causes this fuse to blow, protecting the connection cable between the module and motor.
After blowing the fuse the module is no longer functional and needs to be replaced. The characteristics of the fuse must be checked against the motor data before using the module.
The protection circuit in the module allows a very simple protection of the motor cables. The fuse for the cable protection is a slow-blow one; without short circuit the robust behavior of the module remains.
The motor module is designed to supply the 24 V directly to the motor. At high currents or surges as they occur for example at braking, the module will not be damaged.
The cable protection should be realized outside the motor module with additional measures.
Flat design, installation in cable duct possible
Modules with a flat housing design and with cables which exit the sides make these ideal for installation in cable ducts, cable channels, cable troughs, cable rails or cable trays. Please note the respective housing depth for your particular installation.
Input voltage (sensor supply)
inputs are supplied by ASi or by AUX (auxiliary 24 V power). If supplied by ASi, inputs shall not be connected to earth or to external potential.
|out of AUX|
Output voltage (actuator supply)
Electronic outputs are supplied by ASi or by AUX (auxiliary 24 V power). If supplied by ASi, outputs shall not be connected to earth or to external potential.
For relay outputs the relay contacts are initiated from ASi. The load circuit is powered externally as specified in the data sheet.
||3 x M12 sockets, 5 poles|
Under normal conditions (no bus termination or repeater), the permissible total length of the ASi segment is max. 100 m. The calculation should take into consideration that the length of the connection cable (round cable) for each connected passive distributor must be doubled.
In the case of the active distributors (ASi slaves) however only the one ASi profile cable is counted.
The connection to ASi as well to AUX (auxiliary 24 V power) is made via yellow resp. black ASi profile cable with piercing technology or via M12 socket (in IP20 via clamps).
Line protection: If the module is supplied via a M12 connection with A or B coding, it may only be used with a current load of max. 4 A per pin in acc. with IEC 61076-2-101 and IEC 61076-2-109. A fused tap is recommended. There is no such limitation for modules supplied via piercing contacts.
|ASi via M12|
AB Slave (max. 62 AB Slaves/ASi network), 2 AB Slaves (max. 31 modules with 2 AB Slaves), Single Slaves (max. 31 Single Slaves/ASi network), ASi-5 Slave (max. 62 ASi-5 Slaves/ASi network), mixed use allowed.
For modules with two slaves the second slave is turned off as long as the first slave is addressed to address "0".
Upon request, slaves are available with specific ASi Slave profiles.
|1 Single Slave|