Drive solutions
ASi makes full use of all its strengths in material handling technology. The motor modules for roller drives from Bihl+Wiedemann allow 24V motors to be controlled directly through ASi without the need for an additional control device. The speed of any driven roller can be varied from a central location. Our modules also make it possible to make use of the braking energy of the rollers in the system. Inputs on the modules are used to read in signals from sensors installed along the conveyor line.
In addition to motor modules for roller drives, Bihl+Wiedemann also provides drive solutions for remotely controlling AC motors (with or without frequency inverters) – an essential prerequisite for implementing new system structures.
Drive solutions with Serial Interface
- SEW
- NORD
- EBM-Papst
| Figure | ASi-5/ASi-3 | "SEW MOVIMOT®": Motor module to control geared motors with frequency inverters.
"NORD": Motor module to control geared motors with frequency inverters.
"Itoh Denki (PM605XC/XK)": Motor module to control 24 V motorized rollers Itoh Denki PM605XC/XK.
| Number of Drives | Modules with a flat housing design and with cables which exit the sides make these ideal for installation in cable ducts, cable channels, cable troughs, cable rails or cable trays. Please note the respective housing depth for your particular installation. | Inputs digital | Outputs digital | inputs are supplied by ASi or by AUX (auxiliary 24 V power). If supplied by ASi, inputs shall not be connected to earth or to external potential. | Electronic outputs are supplied by ASi or by AUX (auxiliary 24 V power). If supplied by ASi, outputs shall not be connected to earth or to external potential.
For relay outputs the relay contacts are initiated from ASi. The load circuit is powered externally as specified in the data sheet. | Under normal conditions (no bus termination or repeater), the permissible total length of the ASi segment is max. 100 m. The calculation should take into consideration that the length of the connection cable (round cable) for each connected passive distributor must be doubled. In the case of the active distributors (ASi modules) however only the one ASi profile cable is counted. | The connection to ASi as well to AUX (auxiliary 24 V power) is made via yellow resp. black ASi profile cable with piercing technology or via M12 socket (in IP20 via clamps).
| AB address (max. 62 AB addresses/ASi network), 2 AB addresses (max. 31 modules with 2 AB addresses), Single addresses (max. 31 Single addresses/ASi network), ASi-5 address (max. 62 ASi-5 addresses/ASi network), mixed use allowed. | Article No. |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
 | ASi-5 compatible | SEW MOVIMOT | 1 | no | 4 | 2 x electronic | out of ASi | out of AUX | no | ASi profile cable | 1 ASi-5 address | BWU4068ASi-5 Motor Module, IP67, M12 for SEW MOVIMOT, 1M/4I/2O |
| ASi-5 compatible | NORD frequency inverter (NORDAC FLEX, NORDAC BASE, NORDAC LINK) | 1 | no | 4 | 2 x electronic | out of ASi | out of AUX | no | ASi profile cable | 1 ASi-5 address | BWU4371ASi-5 Motor Module, IP67, M12 for NORD frequency inverter, 1M/4I/2O |
| ASi-5 compatible | EBM-Papst K4 | 1 | no | 4 | 2 x electronic | out of ASi | out of AUX | no | ASi profile cable | 1 ASi-5 address | BWU4370ASi-5 Motor Module, IP67, M12 for EBM-Papst K4, 1M/4I/2O |
| ASi-5 compatible | Rockwell PF525 | 1 | no | 4 | 2 x electronic | out of ASi | out of AUX | no | ASi profile cable | 1 ASi-5 address | BWU4369ASi-5 Motor Module, IP67, M12 for Rockwell PF525, 1M/4I/2O |
| ASi-5 compatible | Bonfiglioli DGM/DGM-R | 1 | no | 4 | 2 x electronic | out of ASi | out of AUX | no | ASi profile cable | 1 ASi-5 address | BWU4388ASi-5 Motor Module, IP67, M12 for Bonfiglioli DGM/DGM-R, 1M/4I/2O |
SEW-EURODRIVE
- SEW MOVIMOT®
- SEW MOVI-SWITCH®
- Separate mounting
- Simple maintenance
| Figure | ASi-5/ASi-3 | "SEW MOVIMOT®": Motor module to control geared motors with frequency inverters.
"NORD": Motor module to control geared motors with frequency inverters.
"Itoh Denki (PM605XC/XK)": Motor module to control 24 V motorized rollers Itoh Denki PM605XC/XK.
| Number of Drives | Modules with a flat housing design and with cables which exit the sides make these ideal for installation in cable ducts, cable channels, cable troughs, cable rails or cable trays. Please note the respective housing depth for your particular installation. | Inputs digital | Outputs digital | inputs are supplied by ASi or by AUX (auxiliary 24 V power). If supplied by ASi, inputs shall not be connected to earth or to external potential. | Electronic outputs are supplied by ASi or by AUX (auxiliary 24 V power). If supplied by ASi, outputs shall not be connected to earth or to external potential.
For relay outputs the relay contacts are initiated from ASi. The load circuit is powered externally as specified in the data sheet. | Under normal conditions (no bus termination or repeater), the permissible total length of the ASi segment is max. 100 m. The calculation should take into consideration that the length of the connection cable (round cable) for each connected passive distributor must be doubled. In the case of the active distributors (ASi modules) however only the one ASi profile cable is counted. | The connection to ASi as well to AUX (auxiliary 24 V power) is made via yellow resp. black ASi profile cable with piercing technology or via M12 socket (in IP20 via clamps).
| AB address (max. 62 AB addresses/ASi network), 2 AB addresses (max. 31 modules with 2 AB addresses), Single addresses (max. 31 Single addresses/ASi network), ASi-5 address (max. 62 ASi-5 addresses/ASi network), mixed use allowed. | Article No. |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
 | ASi-5 compatible | SEW MOVI-C | 1 | yes, depth: 35 mm | 1 | - | out of ASi | - | 1 m | ASi profile cable | 1 ASi-5 address | BWU4718Active Distributor ASi-5 Motor Module for SEW MOVI-C Frequency Inverter, IP67, 1M |
 | ASi-3 compatible | SEW MOVIMOT | 1 | yes, depth: 35 mm | 2 | - | out of AUX | out of AUX | 2 m | ASi profile cable | 1 AB address | BWU3751Active Distributor ASi Motor Module for SEW MOVIMOT with binary control, IP67, 3E/4A |
 | ASi-3 compatible | SEW MOVIMOT | 1 | yes, depth: 35 mm | 2 | - | out of AUX | out of AUX | 2 m | ASi profile cable | 1 AB address | BWU3605Active Distributor ASi Motor Module for SEW MOVIMOT with binary control, IP67, 3I/4O |
 | ASi-3 compatible | SEW MOVIMOT | 1 | yes, depth: 35 mm | 3 | - | out of ASi | out of AUX | M: 2 m, I: 0,3 m | ASi profile cable | 1 AB address | BWU3782Active Distributor ASi Motor Module for SEW MOVIMOT with binary control, IP67, 4I/4O |
 | ASi-3 compatible | SEW MOVIMOT | 1 | yes, depth: 35 mm | 3 | - | out of ASi | out of AUX | M: 1 m, I: 0,3 m | ASi profile cable | 1 Single address | BWU3781Active Distributor ASi Motor Module for SEW MOVIMOT with binary control, IP67, 4I/4O |
 | ASi-3 compatible | SEW MOVIMOT | 1 | yes, depth: 19 mm | 2 | - | out of ASi | - | 2 m | ASi profile cable | 1 Single address | BWU3406Cable Duct ASi Motor Module, IP54, M12 for SEW frequency inverter, 2I |
| ASi-5 compatible | SEW MOVIMOT | 1 | no | 4 | 2 x electronic | out of ASi | out of AUX | no | ASi profile cable | 1 ASi-5 address | BWU4068ASi-5 Motor Module, IP67, M12 for SEW MOVIMOT, 1M/4I/2O |
 | ASi-3 compatible | SEW MOVIMOT | 1 | no | 2 | 1 (Motor) | out of ASi | out of ASi | no | ASi profile cable | 1 Single address | BWU3135ASi Motor Module, IP67, M12 for SEW frequency inverter, 2I |
 | ASi-3 compatible | SEW MOVIMOT | 1 | no | 2 | - | out of ASi | - | no | ASi profile cable | 1 Single address | BWU2912ASi Motor Module, IP67, M12 for SEW frequency inverter, 2I |
| ASi-3 compatible | SEW MOVIMOT | 1 | no | 2 | - | out of AUX | - | no | ASi via M12 | 1 Single address | BWU2956ASi Motor Module, IP67, M12 for SEW frequency inverter, 2I |
| ASi-3 compatible | SEW MOVI-SWITCH 1E | 1 | no | 3 | - | out of ASi | out of ASi | no | ASi profile cable | 1 Single address | BWU2437ASi Motor Module, IP67, M12 for SEW MOVI-SWITCH 1E, 4I/3O |
| ASi-3 compatible | SEW MOVI-SWITCH 1E | 1 | no | 3 | - | out of AUX | out of AUX | no | ASi via M12 | 1 Single address | BWU2957ASi Motor Module, IP67, M12 for SEW MOVI-SWITCH 1E, 4I/3O |
| ASi-3 compatible | SEW MOVI-SWITCH 1E | 2 | no | 4 | 2 x electronic | out of AUX | out of AUX | no | ASi profile cable | 1 AB address | BWU2767ASi Motor Module, IP67, M12, 4I/2O |
| ASi-3 compatible | SEW MOVI-SWITCH 2S, Lenze Smart Motor | 2 | no | 4 | 4 x electronic | out of AUX | out of AUX | no | ASi profile cable | 1 AB address | BWU3032ASi Digital I/O Module, IP67, M12, 4I/4O |
Lenze Smart Motor
- Connections for up to 2 Lenze Smart Motors
- Connections for up to 3 sensors
- Control of up to 5 speeds
- Simple connection of motors via M12 connectors
- Separate mounting
- Simple maintenance
| Figure | ASi-5/ASi-3 | "SEW MOVIMOT®": Motor module to control geared motors with frequency inverters.
"NORD": Motor module to control geared motors with frequency inverters.
"Itoh Denki (PM605XC/XK)": Motor module to control 24 V motorized rollers Itoh Denki PM605XC/XK.
| Number of Drives | Inputs digital | Outputs digital | inputs are supplied by ASi or by AUX (auxiliary 24 V power). If supplied by ASi, inputs shall not be connected to earth or to external potential. | Electronic outputs are supplied by ASi or by AUX (auxiliary 24 V power). If supplied by ASi, outputs shall not be connected to earth or to external potential.
For relay outputs the relay contacts are initiated from ASi. The load circuit is powered externally as specified in the data sheet. | Under normal conditions (no bus termination or repeater), the permissible total length of the ASi segment is max. 100 m. The calculation should take into consideration that the length of the connection cable (round cable) for each connected passive distributor must be doubled. In the case of the active distributors (ASi modules) however only the one ASi profile cable is counted. | The connection to ASi as well to AUX (auxiliary 24 V power) is made via yellow resp. black ASi profile cable with piercing technology or via M12 socket (in IP20 via clamps).
| AB address (max. 62 AB addresses/ASi network), 2 AB addresses (max. 31 modules with 2 AB addresses), Single addresses (max. 31 Single addresses/ASi network), ASi-5 address (max. 62 ASi-5 addresses/ASi network), mixed use allowed. | Article No. |
|---|---|---|---|---|---|---|---|---|---|---|---|
 | ASi-3 compatible | Lenze Smart Motor | 1 | 3 | - | out of AUX | out of AUX | 1 m | ASi profile cable | 1 AB address | BWU3436Active Distributor ASi Motor Module for Lenze Smart Motor, IP67, 4I/3O |
| ASi-3 compatible | Lenze Smart Motor | 1 | 3 | - | out of AUX | out of AUX | 2 m | ASi profile cable | 1 AB address | BWU3787Active Distributor ASi Motor Module for Lenze Smart Motor, IP67, 4I/3O |
 | ASi-3 compatible | Lenze Smart Motor | 1 | 3 | - | out of ASi | out of ASi | 2 m | ASi profile cable | 1 AB address | BWU3640Active Distributor ASi Motor Module for Lenze Smart Motor, IP67, 4I/3O |
| ASi-3 compatible | Lenze Smart Motor | 1 | 3 | - | out of ASi | out of ASi | X2, I2: 2 m, I3/I4: 0,30 m | ASi profile cable | 1 AB address | BWU3784Active Distributor ASi Motor Module for Lenze Smart Motor, IP67, 4I/3O |
| ASi-3 compatible | Lenze Smart Motor | 1 | 4 | 3 x electronic | out of AUX | out of AUX | X2, I2: 2 m, I3/I4: 0,30 m | ASi profile cable | 1 AB address | BWU4740Active Distributor ASi Motor Module for Lenze Smart Motor, IP67, 4I/3O |
 | ASi-3 compatible | Lenze Smart Motor | 1 | 3 | - | out of ASi | out of ASi | no | ASi profile cable | 1 AB address | BWU3886ASi Motor Module, IP67, M12 for Lenze Smart motor, 4I/3O |
| ASi-3 compatible | Lenze Smart Motor | 1 | 3 | - | out of AUX | out of AUX | no | ASi profile cable | 1 AB address | BWU3115ASi Motor Module, IP67, M12 for Lenze Smart motor, 4I/3O |
| ASi-3 compatible | Lenze Smart Motor | 1 | 3 | - | out of AUX | out of AUX | no | ASi via M12 | 1 AB address | BWU3181ASi Motor Module, IP67, M12 for Lenze Smart motor, 4I/3O |
| ASi-3 compatible | SEW MOVI-SWITCH 2S, Lenze Smart Motor | 2 | 4 | 4 x electronic | out of AUX | out of AUX | no | ASi profile cable | 1 AB address | BWU3032ASi Digital I/O Module, IP67, M12, 4I/4O |
Interroll, 24 V/48 V Motorized Rolles
- Interroll EC5000 AI, 24V
- Interroll EC5000 AI, 48V
- Interroll EC200
- Interroll EC300
- Interroll EC310
| Figure | ASi-5/ASi-3 | "SEW MOVIMOT®": Motor module to control geared motors with frequency inverters.
"NORD": Motor module to control geared motors with frequency inverters.
"Itoh Denki (PM605XC/XK)": Motor module to control 24 V motorized rollers Itoh Denki PM605XC/XK.
| Number of Drives | In the motor module UL approved fuses are placed before each of the motor supply connections. A short circuit in the motor causes this fuse to blow, protecting the connection cable between the module and motor. After blowing the not exchangeable fuse the module is no longer functional and the module needs to be replaced. The characteristics of the fuse must be checked against the motor data before using the module. The protection circuit in the module allows a very simple protection of the motor cables. The fuse for the cable protection is a slow-blow one; without short circuit the robust behavior of the module remains.
The motor module is designed to supply the 24 V directly to the motor. At high currents or surges as they occur for example at braking, the module will not be damaged. The cable protection should be realized outside the motor module with additional measures. | Modules with a flat housing design and with cables which exit the sides make these ideal for installation in cable ducts, cable channels, cable troughs, cable rails or cable trays. Please note the respective housing depth for your particular installation. | Inputs digital | Outputs digital | inputs are supplied by ASi or by AUX (auxiliary 24 V power). If supplied by ASi, inputs shall not be connected to earth or to external potential. | Electronic outputs are supplied by ASi or by AUX (auxiliary 24 V power). If supplied by ASi, outputs shall not be connected to earth or to external potential.
For relay outputs the relay contacts are initiated from ASi. The load circuit is powered externally as specified in the data sheet. | Under normal conditions (no bus termination or repeater), the permissible total length of the ASi segment is max. 100 m. The calculation should take into consideration that the length of the connection cable (round cable) for each connected passive distributor must be doubled. In the case of the active distributors (ASi modules) however only the one ASi profile cable is counted. | The connection to ASi as well to AUX (auxiliary 24 V power) is made via yellow resp. black ASi profile cable with piercing technology or via M12 socket (in IP20 via clamps).
| AB address (max. 62 AB addresses/ASi network), 2 AB addresses (max. 31 modules with 2 AB addresses), Single addresses (max. 31 Single addresses/ASi network), ASi-5 address (max. 62 ASi-5 addresses/ASi network), mixed use allowed. | Article No. |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
 | ASi-3 compatible | Interroll (EC310, EC5000 AI, 24 V), Itoh Denki (PM500XC/XK, PM605XC/XK), RULMECA (RDR BL-2) | 2 | yes, separately for each motor, 4,5 A (slow-blow fuse) | yes, depth: 19 mm | 2 | - | out of ASi | out of AUX | 1 m | ASi profile cable | 1 AB address | BWU4224Cable Duct ASi Motor Module, IP54, M8 for 24V motorized rollers, 4I/2O/2AO |
| ASi-3 compatible | Interroll (EC310, EC5000 AI, 24 V), Itoh Denki (PM500XC/XK, PM605XC/XK), RULMECA (RDR BL-2) | 2 | yes, separately for each motor, 4,5 A (slow-blow fuse) | yes, depth: 19 mm | 2 | - | out of ASi | out of AUX | M: 0,40 m, I: 0,06 m | ASi profile cable | 1 AB address | BWU3290Cable Duct ASi Motor Module, IP54, M8 for 24V motorized rollers, 4I/2O/2AO |
| ASi-3 compatible | Interroll (EC310, EC5000 AI, 24 V), Itoh Denki (PM500XC/XK, PM605XC/XK), RULMECA (RDR BL-2) | 2 | yes, separately for each motor, 4,5 A (slow-blow fuse) | yes, depth: 19 mm | 2 | - | out of ASi | out of AUX | M: 0,60 m, I: 1 m | ASi profile cable | 1 AB address | BW3409Cable Duct ASi Motor Module, IP54, M8, M12 for 24V motorized rollers, 4I/2O/2AO |
| ASi-3 compatible | Interroll (EC310), Itoh Denki (PM500XC/XK, PM605XC/XK), RULMECA (RDR BL-2) | 2 | yes, separately for each motor, 3,5 A (slow-blow fuse) | yes, depth: 19 mm | 2 | - | out of ASi | out of AUX | M: 0,60 m, I: 1 m | ASi profile cable | 1 AB address | BW3813Cable Duct ASi Motor Module, IP54, M8, M12 for 24V motorized rollers, 4I/2O/2AO |
 | ASi-5 compatible | Interroll (EC5000 AI, 48 V, 20 W/35 W/50 W) | 2 | yes, separately for each motor, 4,0 A (slow-blow fuse) | no | 4 | - | out of ASi | out of AUX (48 V) | no | ASi profile cable | 1 ASi-5 address | BWU4212ASi-5 Motor Module, IP67, M12 for 48 V motorized rollers, 2M/4I |
| ASi-5 compatible | Interroll (EC5000 AI, 24 V, 20 W/35 W), Itoh Denki (PM500XC/XK, PM605XC/XK), RULMECA (RDR BL-3) | 2 | yes, separately for each motor, 5,0 A (slow-blow fuse) | no | 4 | - | out of ASi | out of AUX | no | ASi profile cable | 1 ASi-5 address | BWU4246ASi-5 Motor Module, IP67, M12 for 24 V motorized rollers, 2M/4I |
 | ASi-3 compatible | Interroll (EC5000 AI, 24 V, 20 W/35 W), Itoh Denki (PM500XC/XK, PM605XC/XK), RULMECA (RDR BL-3) | 2 | yes, separately for each motor, 4,5 A (slow-blow fuse) | no | 2 | - | out of ASi | out of AUX | no | ASi profile cable | 1 AB address | BWU4205ASi Motor Module, IP67, M12 for 24 V motorized rollers, 2M/2I |
| ASi-3 compatible | Interroll (EC310), Itoh Denki (PM500XC/XK, PM605XC/XK), RULMECA (RDR BL-2) | 2 | no | no | 2 | - | out of ASi | out of AUX | no | ASi profile cable | 1 AB address | BWU2575ASi Motor Module, IP67, M12 for 24V motorized rollers, 4I/2O/2AO |
| ASi-3 compatible | Interroll (EC310), Itoh Denki (PM500XC/XK, PM605XC/XK), RULMECA (RDR BL-2) | 2 | no | no | 2 | - | out of AUX | out of AUX | no | ASi via M12 | 1 AB address | BWU2958ASi Motor Module, IP67, M12 for 24V motorized rollers, 4I/2O |
| ASi-3 compatible | Interroll (EC200, EC300), Rollex (Typ 840) | 2 | no | no | 2 | - | out of ASi | out of AUX | no | ASi profile cable | 1 AB address | BWU2398ASi Motor Module, IP67, M12 for 24V motorized rollers, 4I/2O/2AO |
 | ASi-3 compatible | Interroll (EC310), RULMECA (RDR BL-2), Itoh Denki (PM500ME/XE/XP, PM605ME/XE/XP) | 2 | yes, separately for each motor, 4,5 A (slow-blow fuse) | no | 4 | - | out of ASi | out of AUX | no | ASi profile cable | 1 Single address + 1 AB address | BWU2766ASi Motor Module, IP67, M12 for 24V motorized rollers, 4I/4O/2AO |
| ASi-3 compatible | Interroll (EC310), RULMECA (RDR BL-2), Itoh Denki (PM500ME/XE/XP, PM605ME/XE/XP) | 2 | no | no | 4 | - | out of ASi | out of AUX | no | ASi profile cable | 1 Single address + 1 AB address | BWU2478ASi Motor Module, IP67, M12 for 24V motorized rollers, 4I/4O/2AO |
| ASi-3 compatible | Interroll (EC310), RULMECA (RDR BL-2), Itoh Denki (PM500ME/XE/XP, PM605ME/XE/XP) | 2 | no | no | 4 | - | out of ASi | out of AUX | no | ASi via M12 | 1 Single address + 1 AB address | BWU2959ASi Motor Module, IP67, M12 for 24V motorized rollers, 4I/4O/2AO |
Itoh Denki, 24 V Motorized Rolles
- Itoh Denki PM500ME/XE/XK/XP
- Itoh Denki PM605ME/XE/XP
| Figure | ASi-5/ASi-3 | "SEW MOVIMOT®": Motor module to control geared motors with frequency inverters.
"NORD": Motor module to control geared motors with frequency inverters.
"Itoh Denki (PM605XC/XK)": Motor module to control 24 V motorized rollers Itoh Denki PM605XC/XK.
| Number of Drives | In the motor module UL approved fuses are placed before each of the motor supply connections. A short circuit in the motor causes this fuse to blow, protecting the connection cable between the module and motor. After blowing the not exchangeable fuse the module is no longer functional and the module needs to be replaced. The characteristics of the fuse must be checked against the motor data before using the module. The protection circuit in the module allows a very simple protection of the motor cables. The fuse for the cable protection is a slow-blow one; without short circuit the robust behavior of the module remains.
The motor module is designed to supply the 24 V directly to the motor. At high currents or surges as they occur for example at braking, the module will not be damaged. The cable protection should be realized outside the motor module with additional measures. | Modules with a flat housing design and with cables which exit the sides make these ideal for installation in cable ducts, cable channels, cable troughs, cable rails or cable trays. Please note the respective housing depth for your particular installation. | Inputs digital | Outputs digital | inputs are supplied by ASi or by AUX (auxiliary 24 V power). If supplied by ASi, inputs shall not be connected to earth or to external potential. | Electronic outputs are supplied by ASi or by AUX (auxiliary 24 V power). If supplied by ASi, outputs shall not be connected to earth or to external potential.
For relay outputs the relay contacts are initiated from ASi. The load circuit is powered externally as specified in the data sheet. | Under normal conditions (no bus termination or repeater), the permissible total length of the ASi segment is max. 100 m. The calculation should take into consideration that the length of the connection cable (round cable) for each connected passive distributor must be doubled. In the case of the active distributors (ASi modules) however only the one ASi profile cable is counted. | The connection to ASi as well to AUX (auxiliary 24 V power) is made via yellow resp. black ASi profile cable with piercing technology or via M12 socket (in IP20 via clamps).
| AB address (max. 62 AB addresses/ASi network), 2 AB addresses (max. 31 modules with 2 AB addresses), Single addresses (max. 31 Single addresses/ASi network), ASi-5 address (max. 62 ASi-5 addresses/ASi network), mixed use allowed. | Article No. |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ASi-3 compatible | Itoh Denki (PM500XE/XP, PM605XE/XP) | 2 | yes, separately for each motor, 3,5 A (slow-blow fuse) | yes, depth: 19 mm | 4 | - | out of ASi | out of AUX | M: 0,40 m, I: 0,06 m | ASi profile cable | 1 AB address | BWU3278Cable Duct ASi Motor Module, IP54, M8 for 24V motorized rollers, 4I/4O/2AO |
| ASi-3 compatible | Itoh Denki (PM500XE/XP, PM605XE/XP) | 2 | yes, separately for each motor, 3,5 A (slow-blow fuse) | yes, depth: 19 mm | 4 | - | out of ASi | out of AUX | M: 0,40 m, I: 0,40 m | ASi profile cable | 1 AB address | BWU3567Cable Duct ASi Motor Module, IP54, M8 for 24V motorized rollers, 4I/4O/2AO |
| ASi-3 compatible | Itoh Denki (PM500XE/XP, PM605XE/XP) | 2 | yes, separately for each motor, 3,5 A (slow-blow fuse) | yes, depth: 19 mm | 4 | - | out of ASi | out of AUX | M: 0,40 m, I: 0,06 m | ASi profile cable | 1 AB address | BWU3679Cable Duct ASi Motor Module, IP54, M8 and M12 for 24V motorized rollers, 4I/4O/2AO |
 | - | Itoh Denki (PM500XE/XP, PM605XE/XP) | 2 | yes, separately for each motor, 3,5 A (slow-blow fuse) | yes, depth: 18 mm | 2 x light barrier | - | out of AUX | out of AUX | M: 0,43 m, I: 0,09 m, AUX: 0,13 m | - | - | BW3452Passive Cable Duct Motor Module, IP54, M8 for Itoh Denki, 2I |
| ASi-5 compatible | Interroll (EC5000 AI, 24 V, 20 W/35 W), Itoh Denki (PM500XC/XK, PM605XC/XK), RULMECA (RDR BL-3) | 2 | yes, separately for each motor, 5,0 A (slow-blow fuse) | no | 4 | - | out of ASi | out of AUX | no | ASi profile cable | 1 ASi-5 address | BWU4246ASi-5 Motor Module, IP67, M12 for 24 V motorized rollers, 2M/4I |
| ASi-3 compatible | Itoh Denki (PM500XE/XP, PM605XE/XP) | 2 | yes, separately for each motor, 3,5 A (slow-blow fuse) | no | 2 | - | out of ASi | out of AUX | no | ASi profile cable | 1 AB address | BWU2715ASi Motor Module, IP67, M12 for 24V motorized rollers, 2I/4O/2AO |
| ASi-3 compatible | Itoh Denki (PM500XE/XP, PM605XE/XP) | 2 | yes, separately for each motor, 3,5 A (slow-blow fuse) | no | 2 | - | out of ASi | out of AUX | no | ASi profile cable | 1 AB address | BWU3804ASi Motor Module, IP67, M12 for 24V motorized rollers, 2I/4O/2AO |
| ASi-3 compatible | Interroll (EC5000 AI, 24 V, 20 W/35 W), Itoh Denki (PM500XC/XK, PM605XC/XK), RULMECA (RDR BL-3) | 2 | yes, separately for each motor, 4,5 A (slow-blow fuse) | no | 2 | - | out of ASi | out of AUX | no | ASi profile cable | 1 AB address | BWU4205ASi Motor Module, IP67, M12 for 24 V motorized rollers, 2M/2I |
| ASi-3 compatible | Interroll (EC310), RULMECA (RDR BL-2), Itoh Denki (PM500ME/XE/XP, PM605ME/XE/XP) | 2 | yes, separately for each motor, 4,5 A (slow-blow fuse) | no | 4 | - | out of ASi | out of AUX | no | ASi profile cable | 1 Single address + 1 AB address | BWU2766ASi Motor Module, IP67, M12 for 24V motorized rollers, 4I/4O/2AO |
| ASi-3 compatible | Interroll (EC310), RULMECA (RDR BL-2), Itoh Denki (PM500ME/XE/XP, PM605ME/XE/XP) | 2 | no | no | 4 | - | out of ASi | out of AUX | no | ASi profile cable | 1 Single address + 1 AB address | BWU2478ASi Motor Module, IP67, M12 for 24V motorized rollers, 4I/4O/2AO |
| ASi-3 compatible | Interroll (EC310), RULMECA (RDR BL-2), Itoh Denki (PM500ME/XE/XP, PM605ME/XE/XP) | 2 | no | no | 4 | - | out of ASi | out of AUX | no | ASi via M12 | 1 Single address + 1 AB address | BWU2959ASi Motor Module, IP67, M12 for 24V motorized rollers, 4I/4O/2AO |
RULMECA, 24 V Motorized Rolles
- RULMECA RDR BL-2
- RULMECA RDR BL-3
| Figure | ASi-5/ASi-3 | "SEW MOVIMOT®": Motor module to control geared motors with frequency inverters.
"NORD": Motor module to control geared motors with frequency inverters.
"Itoh Denki (PM605XC/XK)": Motor module to control 24 V motorized rollers Itoh Denki PM605XC/XK.
| Number of Drives | In the motor module UL approved fuses are placed before each of the motor supply connections. A short circuit in the motor causes this fuse to blow, protecting the connection cable between the module and motor. After blowing the not exchangeable fuse the module is no longer functional and the module needs to be replaced. The characteristics of the fuse must be checked against the motor data before using the module. The protection circuit in the module allows a very simple protection of the motor cables. The fuse for the cable protection is a slow-blow one; without short circuit the robust behavior of the module remains.
The motor module is designed to supply the 24 V directly to the motor. At high currents or surges as they occur for example at braking, the module will not be damaged. The cable protection should be realized outside the motor module with additional measures. | Modules with a flat housing design and with cables which exit the sides make these ideal for installation in cable ducts, cable channels, cable troughs, cable rails or cable trays. Please note the respective housing depth for your particular installation. | Inputs digital | Outputs digital | inputs are supplied by ASi or by AUX (auxiliary 24 V power). If supplied by ASi, inputs shall not be connected to earth or to external potential. | Electronic outputs are supplied by ASi or by AUX (auxiliary 24 V power). If supplied by ASi, outputs shall not be connected to earth or to external potential.
For relay outputs the relay contacts are initiated from ASi. The load circuit is powered externally as specified in the data sheet. | Under normal conditions (no bus termination or repeater), the permissible total length of the ASi segment is max. 100 m. The calculation should take into consideration that the length of the connection cable (round cable) for each connected passive distributor must be doubled. In the case of the active distributors (ASi modules) however only the one ASi profile cable is counted. | The connection to ASi as well to AUX (auxiliary 24 V power) is made via yellow resp. black ASi profile cable with piercing technology or via M12 socket (in IP20 via clamps).
| AB address (max. 62 AB addresses/ASi network), 2 AB addresses (max. 31 modules with 2 AB addresses), Single addresses (max. 31 Single addresses/ASi network), ASi-5 address (max. 62 ASi-5 addresses/ASi network), mixed use allowed. | Article No. |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ASi-3 compatible | Interroll (EC310, EC5000 AI, 24 V), Itoh Denki (PM500XC/XK, PM605XC/XK), RULMECA (RDR BL-2) | 2 | yes, separately for each motor, 4,5 A (slow-blow fuse) | yes, depth: 19 mm | 2 | - | out of ASi | out of AUX | 1 m | ASi profile cable | 1 AB address | BWU4224Cable Duct ASi Motor Module, IP54, M8 for 24V motorized rollers, 4I/2O/2AO |
| ASi-3 compatible | Interroll (EC310, EC5000 AI, 24 V), Itoh Denki (PM500XC/XK, PM605XC/XK), RULMECA (RDR BL-2) | 2 | yes, separately for each motor, 4,5 A (slow-blow fuse) | yes, depth: 19 mm | 2 | - | out of ASi | out of AUX | M: 0,40 m, I: 0,06 m | ASi profile cable | 1 AB address | BWU3290Cable Duct ASi Motor Module, IP54, M8 for 24V motorized rollers, 4I/2O/2AO |
| ASi-3 compatible | Interroll (EC310, EC5000 AI, 24 V), Itoh Denki (PM500XC/XK, PM605XC/XK), RULMECA (RDR BL-2) | 2 | yes, separately for each motor, 4,5 A (slow-blow fuse) | yes, depth: 19 mm | 2 | - | out of ASi | out of AUX | M: 0,60 m, I: 1 m | ASi profile cable | 1 AB address | BW3409Cable Duct ASi Motor Module, IP54, M8, M12 for 24V motorized rollers, 4I/2O/2AO |
| ASi-3 compatible | Interroll (EC310), Itoh Denki (PM500XC/XK, PM605XC/XK), RULMECA (RDR BL-2) | 2 | yes, separately for each motor, 3,5 A (slow-blow fuse) | yes, depth: 19 mm | 2 | - | out of ASi | out of AUX | M: 0,60 m, I: 1 m | ASi profile cable | 1 AB address | BW3813Cable Duct ASi Motor Module, IP54, M8, M12 for 24V motorized rollers, 4I/2O/2AO |
| ASi-5 compatible | Interroll (EC5000 AI, 24 V, 20 W/35 W), Itoh Denki (PM500XC/XK, PM605XC/XK), RULMECA (RDR BL-3) | 2 | yes, separately for each motor, 5,0 A (slow-blow fuse) | no | 4 | - | out of ASi | out of AUX | no | ASi profile cable | 1 ASi-5 address | BWU4246ASi-5 Motor Module, IP67, M12 for 24 V motorized rollers, 2M/4I |
| ASi-3 compatible | Interroll (EC5000 AI, 24 V, 20 W/35 W), Itoh Denki (PM500XC/XK, PM605XC/XK), RULMECA (RDR BL-3) | 2 | yes, separately for each motor, 4,5 A (slow-blow fuse) | no | 2 | - | out of ASi | out of AUX | no | ASi profile cable | 1 AB address | BWU4205ASi Motor Module, IP67, M12 for 24 V motorized rollers, 2M/2I |
| ASi-3 compatible | Interroll (EC310), Itoh Denki (PM500XC/XK, PM605XC/XK), RULMECA (RDR BL-2) | 2 | no | no | 2 | - | out of ASi | out of AUX | no | ASi profile cable | 1 AB address | BWU2575ASi Motor Module, IP67, M12 for 24V motorized rollers, 4I/2O/2AO |
| ASi-3 compatible | Interroll (EC310), Itoh Denki (PM500XC/XK, PM605XC/XK), RULMECA (RDR BL-2) | 2 | no | no | 2 | - | out of AUX | out of AUX | no | ASi via M12 | 1 AB address | BWU2958ASi Motor Module, IP67, M12 for 24V motorized rollers, 4I/2O |
| ASi-3 compatible | Interroll (EC310), RULMECA (RDR BL-2), Itoh Denki (PM500ME/XE/XP, PM605ME/XE/XP) | 2 | yes, separately for each motor, 4,5 A (slow-blow fuse) | no | 4 | - | out of ASi | out of AUX | no | ASi profile cable | 1 Single address + 1 AB address | BWU2766ASi Motor Module, IP67, M12 for 24V motorized rollers, 4I/4O/2AO |
| ASi-3 compatible | Interroll (EC310), RULMECA (RDR BL-2), Itoh Denki (PM500ME/XE/XP, PM605ME/XE/XP) | 2 | no | no | 4 | - | out of ASi | out of AUX | no | ASi profile cable | 1 Single address + 1 AB address | BWU2478ASi Motor Module, IP67, M12 for 24V motorized rollers, 4I/4O/2AO |
| ASi-3 compatible | Interroll (EC310), RULMECA (RDR BL-2), Itoh Denki (PM500ME/XE/XP, PM605ME/XE/XP) | 2 | no | no | 4 | - | out of ASi | out of AUX | no | ASi via M12 | 1 Single address + 1 AB address | BWU2959ASi Motor Module, IP67, M12 for 24V motorized rollers, 4I/4O/2AO |
Rollex, 24 V Motorized Rollers
- Rollex (Typ 840)
| Figure | ASi-5/ASi-3 | "SEW MOVIMOT®": Motor module to control geared motors with frequency inverters.
"NORD": Motor module to control geared motors with frequency inverters.
"Itoh Denki (PM605XC/XK)": Motor module to control 24 V motorized rollers Itoh Denki PM605XC/XK.
| Number of Drives | In the motor module UL approved fuses are placed before each of the motor supply connections. A short circuit in the motor causes this fuse to blow, protecting the connection cable between the module and motor. After blowing the not exchangeable fuse the module is no longer functional and the module needs to be replaced. The characteristics of the fuse must be checked against the motor data before using the module. The protection circuit in the module allows a very simple protection of the motor cables. The fuse for the cable protection is a slow-blow one; without short circuit the robust behavior of the module remains.
The motor module is designed to supply the 24 V directly to the motor. At high currents or surges as they occur for example at braking, the module will not be damaged. The cable protection should be realized outside the motor module with additional measures. | Modules with a flat housing design and with cables which exit the sides make these ideal for installation in cable ducts, cable channels, cable troughs, cable rails or cable trays. Please note the respective housing depth for your particular installation. | Inputs digital | Outputs digital | inputs are supplied by ASi or by AUX (auxiliary 24 V power). If supplied by ASi, inputs shall not be connected to earth or to external potential. | Electronic outputs are supplied by ASi or by AUX (auxiliary 24 V power). If supplied by ASi, outputs shall not be connected to earth or to external potential.
For relay outputs the relay contacts are initiated from ASi. The load circuit is powered externally as specified in the data sheet. | Under normal conditions (no bus termination or repeater), the permissible total length of the ASi segment is max. 100 m. The calculation should take into consideration that the length of the connection cable (round cable) for each connected passive distributor must be doubled. In the case of the active distributors (ASi modules) however only the one ASi profile cable is counted. | The connection to ASi as well to AUX (auxiliary 24 V power) is made via yellow resp. black ASi profile cable with piercing technology or via M12 socket (in IP20 via clamps).
| AB address (max. 62 AB addresses/ASi network), 2 AB addresses (max. 31 modules with 2 AB addresses), Single addresses (max. 31 Single addresses/ASi network), ASi-5 address (max. 62 ASi-5 addresses/ASi network), mixed use allowed. | Article No. |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ASi-3 compatible | Interroll (EC200, EC300), Rollex (Typ 840) | 2 | no | no | 2 | - | out of ASi | out of AUX | no | ASi profile cable | 1 AB address | BWU2398ASi Motor Module, IP67, M12 for 24V motorized rollers, 4I/2O/2AO |
24 V Motorized Rollers
- 24 VDC motors
| Figure | ASi-5/ASi-3 | "SEW MOVIMOT®": Motor module to control geared motors with frequency inverters.
"NORD": Motor module to control geared motors with frequency inverters.
"Itoh Denki (PM605XC/XK)": Motor module to control 24 V motorized rollers Itoh Denki PM605XC/XK.
| Number of Drives | In the motor module UL approved fuses are placed before each of the motor supply connections. A short circuit in the motor causes this fuse to blow, protecting the connection cable between the module and motor. After blowing the not exchangeable fuse the module is no longer functional and the module needs to be replaced. The characteristics of the fuse must be checked against the motor data before using the module. The protection circuit in the module allows a very simple protection of the motor cables. The fuse for the cable protection is a slow-blow one; without short circuit the robust behavior of the module remains.
The motor module is designed to supply the 24 V directly to the motor. At high currents or surges as they occur for example at braking, the module will not be damaged. The cable protection should be realized outside the motor module with additional measures. | Modules with a flat housing design and with cables which exit the sides make these ideal for installation in cable ducts, cable channels, cable troughs, cable rails or cable trays. Please note the respective housing depth for your particular installation. | Inputs digital | Outputs digital | inputs are supplied by ASi or by AUX (auxiliary 24 V power). If supplied by ASi, inputs shall not be connected to earth or to external potential. | Electronic outputs are supplied by ASi or by AUX (auxiliary 24 V power). If supplied by ASi, outputs shall not be connected to earth or to external potential.
For relay outputs the relay contacts are initiated from ASi. The load circuit is powered externally as specified in the data sheet. | Under normal conditions (no bus termination or repeater), the permissible total length of the ASi segment is max. 100 m. The calculation should take into consideration that the length of the connection cable (round cable) for each connected passive distributor must be doubled. In the case of the active distributors (ASi modules) however only the one ASi profile cable is counted. | The connection to ASi as well to AUX (auxiliary 24 V power) is made via yellow resp. black ASi profile cable with piercing technology or via M12 socket (in IP20 via clamps).
| AB address (max. 62 AB addresses/ASi network), 2 AB addresses (max. 31 modules with 2 AB addresses), Single addresses (max. 31 Single addresses/ASi network), ASi-5 address (max. 62 ASi-5 addresses/ASi network), mixed use allowed. | Article No. |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ASi-3 compatible | 24 V DC motors | 2 | no | no | 2 | - | out of AUX | out of AUX | no | ASi profile cable | 1 AB address | BWU3501ASi Motor Module, IP67, M12 for 24 V motorized rollers, 2I/4O |
| ASi-3 compatible | 24 V DC motors | 1 | no | no | 4 | 2 x electronic | out of ASi | out of AUX | no | ASi profile cable | 1 Single address | BWU3551ASi motor module, IP67, M12 for 24 V DC motor, 4I/2O |